copy and paste this google map to your website or blog!
Press copy button and paste into your blog or website.
(Please switch to 'HTML' mode when posting into your blog. Examples: WordPress Example, Blogger Example)
Input Form:Deal with this potential dealer,buyer,seller,supplier,manufacturer,exporter,importer
(Any information to deal,buy, sell, quote for products or service)
Question: - Andu Engraver - The Engravers Cafe I actually bought the Andu hand control graver and returned it a week later It started to fall apart about 3 hours into running it In concept, it worked, but it was too fragile to be worth even the discount price I would get the Lindsay or GRS units, don't waste your money on the Andu
Question: - Andu Engraver | Page 4 | The Engravers Cafe I feel I can chime in on this one When getting started I bought an Andu handpiece It worked well enough for me to enjoy engraving and learing I was fortunate enough to try out a GSR GraverMach AT and I instantly bought the GraverMach setup The Andu works okay for medium sized scroll backbones
Question: - Andu Engraver | Page 3 | The Engravers Cafe I bought the Andu then, because I wanted a Lindsay but didn't know if it would be the setup for me or maybe a GRS or whatever else And because I needed to save up for a Lindsay It was the Andu that made me decide on saving up for a Lindsay though I just got my Lindsay and I have to admit that there is a vast difference in performance
Question: - Andu Engraver | Page 2 | The Engravers Cafe I'm running the andu footcontrol graver at the moment, simply because with this whole covid thing going on, I don't have the money to spend on a Lindsay While I'm running the andu, I'm saving up for a Lindsay classic with banknote handle And while I'm saving up, I can run something similar and get a feel for engraving with basically the same
Question: Andu Bulino pen quality?? - The Engravers Cafe If you have access to any basic machine tools you could just make a slender pen-like back for your Lindsay classic probably need a piece of 5 8 " rod, could be steel, but brass would be easier to shape if you have to do it with hand tools it just needs to be to large enough to put a 1 2" flat bottomed hole in one end, the hole in the mushroom shaped handle on it is about 9 16" deep but you
Upgrade: compressor or engraving system? | The Engravers Cafe Hi everyone At the moment, I’m using a small airbrush compressor, the Original Fengda FD-18A, with an Andu system (it is what I could afford for start) It seems like it doesn’t push much, and in any case, it doesn’t maintain the initial power Do you think it would be better to upgrade the
Question: Cheaper power hones available? - The Engravers Cafe Sounds as though you have eliminated most of the options I have a power hone that was purchased in the beginning of this endeavor, currently it is only being used for the shaping of the graver blanks, after the initial shape and sharpening all of my graver maintenance is carried out with the Lindsay templates and bench stones
Reversing graver sharpener. | The Engravers Cafe I recently purchased an Andu graver sharpening unit that rotates in a counter clockwise direction My graver holding fixture (post, duel angle type) would work better if the sharpener would turn clockwise It doesn't use a standard plug in to the motor but rather a "jack" type plug in so I don't know how to reverse the wiring Any suggestions
introduction: Hi, Im Caleb | The Engravers Cafe I picked up a super cheap graver (andu graver, the basic non-palm control one ) and a ball vise I figured I'd lose interest after a little bit I started practicing on brass blanks I really enjoyed engraving and started to feel like this is something I should stick with, past the usual plateau of figuring out the basics
Hand Engraving Forum | Page 18 | The Engravers Cafe Learn hand engraving! EngraversCafe com is the world's largest hand engraving community! Thousands of members learn, share, inspire, and make friends with